On Your Own Love Again Vinyl
Vinyl siding installation should be left to the pros unless you lot're confident that y'all have adequate carpentry skills and feel. The upside of doing the project yourself is that you can cutting the cost of installation to most half of what you will likely shell out to hire a contractor. The installation of vinyl siding itself is not that hard, merely it does require proper planning as well as precise measurements, calculations, cuts and leveling to ensure that the panels fit your wall perfectly.
The steps for vinyl siding installation beneath presume that you have completed installing the panels for the soffit, which is the underside of the roof overhang, and the fascia, which is the horizontal band along the bottom of the roof. For this projection, y'all will need the following tools:
Power saw Hammer Tin snips Utility knife Record mensurate Chalk line Level Ladder
Apart from vinyl siding panels, the other needed materials are:
Starter strips J-trims Corner moldings Utility trims Drip caps Housewrap and A lot of nails, preferably those with wider heads Plywood
Continue in mind that even many pros prefer non to take this job on alone. Have one or two friends help you lot. Once you have all tools and materials listed above, you're fix to accept on this vinyl siding installation DIY.
Step Remove Obstacles
Clear the wall of anything that will get in the manner of the vinyl siding such as exterior lamps, retractable clothesline spools, address plates or old vinyl sidings. Plan the disposal of your old siding properly. Don't mess with utility fixtures or the electrical meter. Y'all need to work around them.
Take Measurements
Measure from the eave downwards to the lesser where you'll nail the starter strip. Most vinyl sidings are 12 feet long and 8 inches wide. This ways that if the distance between the eave and the bottom is divisible past eight inches, you can connect your elevation panel directly to the J-trim. About of the time, however, y'all will have to modify your final top panel and use a utility trim to install this final slice.
Notice Your Level Points
Detect the level points at the bottom for the starter strip and mark them with the chalk line. Try to be as precise as possible with the level points. This volition make the job easier as y'all start installing the vinyl siding.
Attach the Starter Strip and Vertical Trims
Align the starter strip carefully forth the chalk line and blast information technology firmly to the wall. Nail 3 ½ inch by ½ inch plywood pieces along the height of the starter strip to make it sturdier and assistance it concur upwards the vinyl siding panels. Next, adhere the vertical trims, including the corner posts and cease channels. You may also attach the trims around the windows and doors at this point.
Cut the Vinyl Sidings Co-ordinate to Length
Measure out the distance between the vertical end posts and cut the vinyl panels according to length for each row. Permit for a ¼ inch distance between the end of the siding and the corner post. Increase the distance to ⅜ inch in areas where the temperatures go as low as 40 degrees Fahrenheit. Vinyl siding expands and contracts forth with temperature fluctuations. The gap volition prevent harm to the siding.
Install the Vinyl Sidings
Sheath the first few anxiety above the starter strip with the insulation or wet protection material, and then snap and lock the start vinyl siding row on the starter strip. Nail the panels every maximum of sixteen inches on the framing studs or furring on the wall. It is important to remember not to blast the vinyl sidings tightly against the wall and position the nail at the center of the slot; leave a ane/32 inch gap between the nail head and the vinyl siding. Yous've installed each panel correctly if the siding can freely move from side to side. When you demand to overlap panels to bridge a gap between posts, brand sure that the panels overlap by about an inch. Piece of work your manner upwardly around the wall cutting around doors, windows and lamps using the tin snip.
End Up
Equally you lot reach the soffit on the eaves, measure the width that you lot need for the last piece in several locations and modify the vinyl siding panel according to the measurements. Install a J-aqueduct. Make tabs on the cut edge of the panel every six inches using a snap lock punch. Install a utility trim into the J-channel. Lock in the last panel that you have modified on the final row and snap it into the utility trim on top of the wall.
Source: https://www.questionsanswered.net/article/how-to-install-vinyl-siding?utm_content=params%3Ao%3D740012%26ad%3DdirN%26qo%3DserpIndex
0 Response to "On Your Own Love Again Vinyl"
Post a Comment